UltraProp II 3 Blade Propeller
Ultra-Prop II Propellers
The Ultra-Prop II uses the same patented blade, hub and pitch block system as the original Ultra-Prop, which has been in continuous production since 1983. It will remain in production and sold here.
The new key components of the Ultra-Prop II are the carbon reinforced blade, the pitch blocks and the special blade clamping bolts. The Ultra-Prop II is 60-66 inches in diameter in the 2, 3 and 4-blade hub; The blades may be cut to any lesser diameter without need for any special tip finishing or re-balancing. Just measure twice, cut once per blade. We do this for you if you order a smaller diameter propeller.
The new blade is a stiff solid composite (no foam core, etc.), has a conventional plan form with the appropriate blade twist (helix) and has a highly efficient airfoil. The carbon reinforced engineering thermoplastic blade surface is very hard and durable to withstand abrasion and water impact much better than other blades made or coated with epoxy or other similar 2-part resins. The operating temperature range is - 60 degrees F to +350 degrees F.
Blade pitch range is 8 to 18 degrees, adjusted in one degree increments by changing pitch block sets. No protractor required! The new engineering structural thermoplastic used is long carbon fiber strand reinforced for high strength, stiffness and low weight. The blades and hub are weather resistant, UV protected and suitable for use on the water and in rain for airboat, hovercraft and Sport or Experimental aircraft such as ultralights, large drones, Unmanned Aerial Vehicles ( UAV ) home-built and kit planes.
Propeller kit comes with hub, crush plate, mounting bolts, 3 blades, and 3 sets of pitch blocks.
**Specify engine and gear box ratio when purchasing**
Ultra-Prop II Propellers
The Ultra-Prop II uses the same patented blade, hub and pitch block system as the original Ultra-Prop, which has been in continuous production since 1983. It will remain in production and sold here.
The new key components of the Ultra-Prop II are the carbon reinforced blade, the pitch blocks and the special blade clamping bolts. The Ultra-Prop II is 60-66 inches in diameter in the 2, 3 and 4-blade hub; The blades may be cut to any lesser diameter without need for any special tip finishing or re-balancing. Just measure twice, cut once per blade. We do this for you if you order a smaller diameter propeller.
The new blade is a stiff solid composite (no foam core, etc.), has a conventional plan form with the appropriate blade twist (helix) and has a highly efficient airfoil. The carbon reinforced engineering thermoplastic blade surface is very hard and durable to withstand abrasion and water impact much better than other blades made or coated with epoxy or other similar 2-part resins. The operating temperature range is - 60 degrees F to +350 degrees F.
Blade pitch range is 8 to 18 degrees, adjusted in one degree increments by changing pitch block sets. No protractor required! The new engineering structural thermoplastic used is long carbon fiber strand reinforced for high strength, stiffness and low weight. The blades and hub are weather resistant, UV protected and suitable for use on the water and in rain for airboat, hovercraft and Sport or Experimental aircraft such as ultralights, large drones, Unmanned Aerial Vehicles ( UAV ) home-built and kit planes.
Propeller kit comes with hub, crush plate, mounting bolts, 3 blades, and 3 sets of pitch blocks.
**Specify engine and gear box ratio when purchasing**
Ultra-Prop II Propellers
The Ultra-Prop II uses the same patented blade, hub and pitch block system as the original Ultra-Prop, which has been in continuous production since 1983. It will remain in production and sold here.
The new key components of the Ultra-Prop II are the carbon reinforced blade, the pitch blocks and the special blade clamping bolts. The Ultra-Prop II is 60-66 inches in diameter in the 2, 3 and 4-blade hub; The blades may be cut to any lesser diameter without need for any special tip finishing or re-balancing. Just measure twice, cut once per blade. We do this for you if you order a smaller diameter propeller.
The new blade is a stiff solid composite (no foam core, etc.), has a conventional plan form with the appropriate blade twist (helix) and has a highly efficient airfoil. The carbon reinforced engineering thermoplastic blade surface is very hard and durable to withstand abrasion and water impact much better than other blades made or coated with epoxy or other similar 2-part resins. The operating temperature range is - 60 degrees F to +350 degrees F.
Blade pitch range is 8 to 18 degrees, adjusted in one degree increments by changing pitch block sets. No protractor required! The new engineering structural thermoplastic used is long carbon fiber strand reinforced for high strength, stiffness and low weight. The blades and hub are weather resistant, UV protected and suitable for use on the water and in rain for airboat, hovercraft and Sport or Experimental aircraft such as ultralights, large drones, Unmanned Aerial Vehicles ( UAV ) home-built and kit planes.
Propeller kit comes with hub, crush plate, mounting bolts, 3 blades, and 3 sets of pitch blocks.
**Specify engine and gear box ratio when purchasing**
